Lab Topology:
Please use the following topology to complete this lab exercise:
Task 1:
Configure the hostnames on routers R1 and R2 as illustrated in the topology.
Task 2:
Configure a back-to-back Serial connection between R1 and R2. Configure the DCE interface Serial0/0 in R2 to provide clocking to R1 at a clock speed of 2 Mbps (if this is the DCE end). Configure IP addresses 192.168.0.1/30 and 192.168.0.2/30 on R1 and R2 Serial0/0 interfaces, respectively. Configure the Loopback interfaces on R1 with the IP addresses illustrated in the topology.
Task 3:
Enable RIPv2 on R1 and configure RIPv2 routing for the Loopback interfaces and the Serial0/0 interface. Verify on either R1 or R2 that RIPv2 has been enabled using the appropriate commands.
Configuration and Verification
Task 1:
For reference information on configuring hostnames, please refer to earlier labs.
Task 2:
R2#conf t
Enter configuration commands, one per line. End with CTRL/Z.
R2(config)#int s0/0
R2(config-if)#clock rate 2000000
R2(config-if)#end
R2#
R2#sh controllers s0/0
Interface Serial0/0
Hardware is PowerQUICC MPC860
DCE V.35, clock rate 2000000
R1#conf t
Enter configuration commands, one per line. End with CTRL/Z.
R1(config)#int s0/0
R1(config-if)#ip add 192.168.0.1 255.255.255.252
R1(config-if)#no shutdown
R1(config)#int loop100
R1(config-if)#ip add 10.10.100.1 255.255.255.224
R1(config-if)#exit
R1(config)#int loop101
R1(config-if)#ip add 10.10.101.1 255.255.255.192
R1(config-if)#end
R1#
R2#conf t
Enter configuration commands, one per line. End with CTRL/Z.
R2(config)#int s0/0
R2(config-if)#ip address 192.168.0.2 255.255.255.252
R1(config-if)#no shutdown
R2(config-if)#end
R2#
R1#ping 192.168.0.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
R2#ping 192.168.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
Task 3:
R1#conf t
Enter configuration commands, one per line. End with CTRL/Z.
R1(config)#router rip
R1(config-router)#version 2
R1(config-router)#network 10.0.0.0
R1(config-router)#network 192.168.0.0
R1(config-router)#end
R1#
R2#conf t
Enter configuration commands, one per line. End with CTRL/Z.
R2(config)#router rip
R2(config-router)#version 2
R2(config-router)#network 192.168.0.0
R2(config-router)#end
R2#
NOTE: When configuring RIP routing, you must use the version 2 keyword under RIP configuration mode. By default, if RIP is enabled and this keyword is not issued, the Cisco IOS router will enable both RIPv1 and RIPv2. RIPv1 will be enabled for inbound and outbound routing updates, and RIPv2 will be enabled only for inbound routing updates. This is illustrated below for a router configured for RIP routing without the version 2 keyword:
R1#show ip protocols
Routing Protocol is “rip”
Sending updates every 30 seconds, next due in 9 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 1, receive any version
Interface Send Recv Triggered RIP Key-chain
Serial0/0 1 1 2
The next thing to remember when enabling RIP is to always specify the network at its major classful boundary, regardless of the fact that it has been subnetted. For example, R1 has two Loopback interfaces: 10.10.100.1/27 and 10.10.101.1/26. Because these are part of the 10.0.0.0/8 subnet (which is a Class A address) the RIP network statement is configured using their major classful boundary and is configured as network 10.0.0.0 in RIP configuration mode.
R1#show ip protocols
Routing Protocol is “rip”
Sending updates every 30 seconds, next due in 12 seconds
Invalid after 180 seconds, hold down 180, flushed after 240
Outgoing update filter list for all interfaces is not set
Incoming update filter list for all interfaces is not set
Redistributing: rip
Default version control: send version 2, receive version 2
Interface Send Recv Triggered RIP Key-chain
Serial0/0 2 2
Loopback100 2 2
Loopback101 2 2
Automatic network summarization is in effect
Maximum path: 4
Routing for Networks:
10.0.0.0
192.168.0.0
Routing Information Sources:
Gateway Distance Last Update
192.168.0.2 120 00:02:47
Distance: (default is 120)